Minolta PI4700E Manual de usuario descargar pdf (Pagina 33)

Di470

Solution

Any support for the AHT products, OneRIP 1 and OnCore, is handled by AHT directly. By contract, AHT provides hotline support.

From within the U.S.

Tel: 1-310-214-8600

Fax: 310-214-8697

E-mail: [email protected]

From outside the U.S.

Tel: 1-310-214-8600

Fax: 1-310-214-8697

E-mail: [email protected]

* Trademark ownership information

Solution ID

Solution Usage

TAUS0653248EN*

Description

Part number for the PCMCIA Flash Card.

Solution

8MB PCMCIA Flash Card (p/n 766080135).

Notes:

1. Card Specifications - 8MB Programmable Flash Card, AMD "D" Series, Type 1 Linear, 5V DC only, operation with minimum of 200ns access time from

standby.

2. Use the SwapFTL_Utility and current firmware located on the [[Konica Minolta FTP site| URL ftp://kbtdigital:[email protected]]].

Solution ID

Solution Usage

TAUS0654704EN*

Description

How to upgrade PCMCIA flash cards to a higher flash ROM version.

Solution

To re-write a flash card with a new version of flash ROM data a PCMCIA card slot and the appropriate software are needed.

Notes:

1. One program commonly used for this purpose is Elan Memory Card Explorer.

2. For details on the procedure to upgrade the machine's flash rom, please refer to pages D-118 through D-122 of the Field Service Manual .

3. To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* web site at:

[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]

* Trademark ownership information

Solution ID

Solution Usage

TAUS0656006EN*

Description

Why does pagination change when printing any document using the Konica Minolta print driver?

Solution

Explaining pagination differences between different manufacturers print drivers:

This situation is not uncommon in the printing world. Commonly, documents will be formatted differently when printed to printers made by different

manufacturers. There are many reasons for this. Due to physical differences between printers, as well as copyright laws, different manufacturers will use

different programs for their drivers. It is the driver that does the majority of the formatting for the image to be placed on the page. Different drivers will use

different algorithms when imaging spacing and font metrics. Often times, this results in a slightly different look or format for a document when printed to two

different printers.

There is also potential differences within the image areas of the main bodies of the two printers. The print controller takes the image area into account when

laying out the image on the paper. Different image areas can determine different layouts. These factors can result in lines of text being moved on the paper.

If lines are moved enough, or lie close enough to the threshold of the image area, text and page breaks that are rendered in a certain position on one printer

may be rendered in a different position on another.

This scenario will occur across the board for printer manufacturers. A Lexmark* is different from an Epson* which is different than an HP*, etc. Obviously, the

output from certain printers will match up closer to some printers than others. The effect of this behavior can be reduced somewhat by printing with a

common standard PDL such as PostScript*. Alternatively, the customer can print with a common driver to both printers. In other words, one can print to the

HP using the Konica driver or vice versa. In this way, at least the driver-generated output would be the same going to both machines. While the output still

may not be exactly the same, the effect of printing to two different printers can be lessened. There may even be different output within the same printer

manufacturer (i.e., Konica IP302 print controller is good, but the IP304 print controller is not; Lexmark Optra K1220 is good, but the Optra T614 is not).

The analogy that is often used when explaining this to customers involves motor vehicles. A Ford and Dodge are essentially the same in terms of the fact that

they are cars that serve as a means of transportation, just as two printers are output devices. However, while the end result of driving two different cars is

essentially the same, there may be certain differences with regard to cornering and acceleration that give each car a distinct feel. This is essentially what is

happening between the two printers.